andre.taylor@beltzhoovergatesdoors.com
  • Serving Pittsburgh Since 2007
  • Fully Licensed & Insured
  • Committed to Your Satisfaction
  • Locally Owned
  • Committed to Showing Up On Time
Call (412) 226-4495

Gate Repair in Pittsburgh

Gate repair puts the gate you already have back in working order. It covers manual and powered gates, swing and slide, at homes, apartment communities, churches, small businesses and the fenced yards behind warehouses. Some properties have one driveway gate; others have a vehicle entrance with a walk-through gate beside it. We work on both.

Gate faults usually start in the parts that carry the weight: the posts, the hinges and the frame. A leaning post or a worn hinge lets the leaf drop, and from there it drags, binds at the latch and strains whatever opens it. In Our Process, the hinges, posts and track are checked before anyone touches the operator.

Signs You Need Gate Repair

  • The gate sags or drags. A leaf that has dropped at its latch end scrapes the drive, usually because of a worn hinge, a loose hinge fixing or a hinge post that has begun to lean.
  • It will not latch. When the latch misses its keeper, something has moved: the leaf has sagged, a post has shifted or the latch has been knocked out of line.
  • The hinges squeal or pull from the post. A squeal points to dry or worn hinge pins. A hinge plate working loose or easing away from the post means its fixing is failing under the weight of the gate.
  • The frame is bent or cracked. A bent rail, a cracked weld or a twisted corner throws the leaf out of square, so it binds even on sound hinges.
  • The gate swings by itself. A gate that drifts open or shut on its own usually hangs from a hinge post out of plumb, so the leaf settles toward the low side. On a powered gate, the operator may have been left on its manual release.

Straightening, Rehanging and Repairing the Gate

Heavy barrel hinge bolted to the frame of a black steel gate, a perforated steel panel beside it

On a manual gate, or on the gate behind an operator, the repair is mostly structural. We straighten sagging posts and hinges; worn hinges are reset or replaced, the leaf is rehung so it swings level and clears the ground, and the latch is brought back into line with its keeper.

Frame repair depends on the material. A bent rail or a cracked weld on a steel or aluminum frame can often be straightened or welded, and a wood gate with loose joints can be squared and braced.

A gate that sags again soon after it is rehung usually has a post problem. Steep driveways load the hinge post harder than level ones, and a post that has leaned or heaved has to be set plumb and firm before any hinge will hold the leaf.

Repairs to a Powered Gate

When the gate has an operator, the fault may sit in the gate, the operator or the controls, and the symptoms overlap: a leaf dragging on a worn hinge stalls the operator just as a worn motor does. We trace the fault, adjust limit switches, and replace worn motors, control boards and safety sensors. A structural fault has to be put right first, or the operator goes on pushing against a binding leaf.

The Gate Parts a Repair Puts Right

Gate parts and how their failure shows
Gate part What it does What failure looks like
Hinge post Carries the full weight of the leaf and holds it plumb. The post leans or rocks, and the leaf drops at the latch end.
Hinges Let the leaf turn and hold it at the right height. Squealing, play at the pin, or a plate pulling from the post.
Frame and rails Keep the leaf square and stiff. A bent rail, a cracked weld, loose joints or a twisted corner.
Latch and keeper Hold the gate shut against the latch post. The latch misses its keeper, or the gate has to be lifted to catch.
Drop rod or center stop Keeps the two leaves of a double gate in line where they meet. Leaves that meet unevenly, or a rod that no longer drops into its socket.
Operator and control board Drive a powered gate and run each open and close cycle. The gate stalls, grinds, stops halfway or ignores the remote.
Limit switches and sensors Tell the operator where to stop, and stop it when something is in the way. The gate stops short, overruns, or reverses with nothing in its path.

Double Drive Gates at Commercial Lots

Wide chain-link drive gates at warehouses and small businesses fail in the same places as a driveway gate, only harder. Each leaf hangs a long way from its hinges, so a worn hinge or a leaning post drops it below its partner at the center, and a drop rod that misses its socket lets the pair swing open in the wind.

Chain-link double drive gate closing off the lane between two metal warehouse buildings
Galvanized chain-link fence and gate frame along a metal building beside an asphalt lot

When a Repair Makes Sense and When a Gate Is Worn Past Saving

Whether to repair or replace gets a plain answer, and these points usually decide it.

  • The posts are sound, or can be made sound. A post that can be straightened and set firm gives a rehung leaf something to hold, so a sagging gate on sound posts is usually a repair.
  • The damage is local. One bent rail, cracked weld or broken picket can be put right. Damage through the whole frame usually costs more to repair than the gate is worth.
  • Rust is on the surface, not through the metal. Surface rust can be cleaned back and painted. Steel rusted through at the bottom rail, the welds or the hinge mounts has lost its strength.
  • The wood is solid. Loose joints can be squared and braced, but rot in the rails or around the hinges leaves the fixings nothing to hold.
  • The same fault keeps coming back. A gate that needs the same repair season after season, or was built too light for its opening, is often better replaced with a new gate built for the job.

Fixing a Damaged Gate

Can a gate with a bent frame be straightened, or does it need replacing?

A frame bent in one place, such as a rail pushed in by a bumper, can usually be straightened or the damaged section cut out and welded. When the bend runs through the whole frame, or the welds around it have cracked, the leaf rarely comes back square, and a new gate is the sounder choice.

Is a gate that was hit by a car worth repairing?

That depends on what took the blow. A bent leaf on sound posts is often a repair. A post knocked out of plumb or loosened in its footing has to be reset first, and an operator that was struck needs its arm, its mounting and its limits checked as well.

Can a gate be saved if its post has broken?

Often it can. The usual fix for a post that has snapped, rotted at the base or cracked out of its footing is a new post, with the leaf rehung on it. If the leaf itself is sound, the gate does not have to go with the old post.

Have a Dragging or Stalled Gate Looked At

Call or schedule a visit and say what the gate is doing. Whether it needs a repair or a new gate, you will get a straight answer.