Gate Glossary in Plain Words
Gate work has its own vocabulary, and a few of its words go a long way. “The gate stops short of its limit” tells a technician more than “the gate is broken,” and knowing a hinge from a keeper makes a repair easier to follow.
None of these words is needed to book a visit: describing what the gate does is enough. They are most useful for seeing how a gate fits together, from its posts and hinges to its operator, and how a fault in one part shows up in the next.
Terms Used for Gates, Openers and Entry Controls
Each term is set out in plain words, with where it tends to come up and the service it belongs to.
Find a Term
Type a word or choose a letter, then press Filter the Terms.
| Term | Plain-words meaning | Where you will hear it | Related service |
|---|---|---|---|
| Articulated arm | The jointed arm of a swing gate operator, which folds and straightens like an elbow to open and close the leaf. | Swing operator repairs, when a joint wears loose | Automatic Gate Openers |
| Cantilever gate | A sliding gate carried on rollers mounted on posts beside the opening, so it rides clear of the ground with no track. | Sliding gates across gravel or uneven drives | Gate Installation |
| Control board | The circuit board in the operator that reads remotes, keypads and sensors and tells the motor when to start, stop and reverse. | Openers that quit after a power surge or a leak | Automatic Gate Openers |
| Drop rod (cane bolt) | A sliding rod on one leaf of a double gate that drops into a hole in the ground to hold that leaf in place. | Double gates that blow open or close out of line | Gate Repair |
| Exit loop | A wire loop buried in the drive inside the gate that senses a car’s metal and opens the gate for traffic leaving. | Busy entrances where drivers leave without a remote | Access Control |
| Frame | The outer rails and uprights that give a gate leaf its shape, with the pickets, panels or boards fixed inside. | A gate struck by a car or twisted out of square | Gate Repair |
| Gate stop | A fixed block, post or plate the gate closes or opens against, so it halts in the same place every time. | Gates that over-swing, or operators that strain at the end of travel | Gate Repair |
| Gooseneck post | A short post with a curved top that holds a keypad or intercom at a driver’s window height. | Placing a keypad within reach of a car window | Access Control |
| Hinge | The pivot a swing gate hangs from. Heavy gates hang on barrel, strap or ball-bearing hinges fixed to the post and frame. | Gates that sag, squeal or swing unevenly | Gate Repair |
| Intercom | A call station at the gate linked to a handset inside, so a visitor can ask someone to open the gate. | Apartment entrances, churches and gates far from the house | Access Control |
| Keeper (strike) | The part on the post or the second leaf that a latch catches in. When a gate drops, the latch misses it. | Gates that will not latch, or rattle when closed | Gate Repair |
| Keypad | A weatherproof panel of number buttons at the gate that opens it when a valid code is entered. | Code changes, sticking buttons and new entry controls | Access Control |
| Latch | The catch that holds a gate closed against its keeper. A latch holds the gate shut; a lock keeps it from being opened. | A gate that swings open on its own in the wind | Gate Repair |
| Leaf | One moving panel of a gate. A single gate has one leaf; a double or bi-parting gate has two. | Double driveway gates, and operators fitted one to each leaf | Know Your Gate |
| Limit switch | The switch or setting that tells an operator where fully open and fully closed are. Out of adjustment, it stops the gate short. | A gate that stops partway or bangs into its stop | Automatic Gate Openers |
| Manual release | The key, lever or knob that disconnects an operator from its gate so the gate can be moved by hand. | Power outages, and operators that have failed | Automatic Gate Openers |
| Operator | The powered unit that opens and closes an automatic gate, also called a gate opener: motor, gearbox and control board. | Any work on an automatic gate | Automatic Gate Openers |
| Photo-eye | A pair of sensors facing each other across the opening. When something breaks the beam between them, the gate stops or reverses. | A gate that will not close, or reverses with nothing in the way | Gate Maintenance |
| Pier | A gate post built of brick, stone or block instead of steel or wood, usually wider and much heavier. | Hanging a gate or mounting an operator on masonry | Gate Installation |
| Post | The upright a gate hangs from or closes against, set in concrete. A leaning post pulls the whole gate out of line. | Sagging gates, and latches that no longer meet | Gate Repair |
| Rack and pinion | The drive on many slide gate operators: a toothed rack along the gate, moved by a small gear, the pinion, on the operator. | Slide gates that grind, slip or stop short | Automatic Gate Openers |
| Roller | A wheel that carries a sliding gate, along a ground track or, on a cantilever gate, in a roller assembly on the posts. | Slide gates that drag, jump or run rough | Gate Maintenance |
| Safety edge | A pressure-sensitive rubber strip along a gate’s edge that signals the operator to stop and reverse when it touches something. | Gates that reverse for no visible reason | Automatic Gate Openers |
| Sag | A leaf dropping at its latch end, usually from a loose hinge, a leaning post or a frame out of square. | Older swing gates that scrape across the drive | Gate Repair |
| Slide gate | A gate that opens by moving sideways along the fence line, on a track or cantilevered, instead of swinging. | Wide openings, and drives with no room for a gate to swing | Gate Installation |
| Swing gate | A gate hung on hinges that opens by swinging in or out like a door, as a single leaf or a pair. | Driveway and walk-through gates of every size | Gate Installation |
| Track | The rail in or on the ground that a sliding gate’s wheels run along. Debris or a bent section can stop the gate. | Slide gates that stall at the same spot every time | Gate Maintenance |
| Transmitter (remote) | The handheld remote that signals the gate’s receiver to open. Each one is stored in the receiver’s memory. | Lost remotes, and remotes that work only up close | Access Control |
Gate Terms That Are Often Confused
Is a gate operator the same thing as a gate opener?
Yes. Operator is the trade’s word and opener the everyday one; both mean the powered unit that opens and closes an automatic gate. It is often called the motor too, though the motor is only one part of it, beside the gearbox and the control board.
What is the difference between a latch and a lock?
A latch holds a gate closed; a lock keeps anyone without a key or a code from opening it. Many latches hold well but lock nothing, and some take a padlock to do both. On many automatic gates there is no latch at all, because the operator holds the leaf closed.
Do photo-eyes and safety edges do the same job?
They share a purpose, keeping a moving gate off a car or a person, but they work differently. A photo-eye reacts before anything is touched, when its beam is broken; a safety edge reacts on contact, when its strip is pressed. Many gates carry both, and a failed one is part of automatic gate opener repair.
How do swing, slide and cantilever gates differ?
A swing gate turns on hinges like a door and needs clear room to swing. A slide gate moves sideways along the fence line, usually on wheels in a ground track. A cantilever gate is a slide gate without the track: it hangs from rollers on posts beside the opening, so nothing crosses the drive.